[Cisco Dumps 100% Pass] Latest Cisco 100-150 Dumps PDF Training Resources And VCE Youtube Update

High quality Cisco ICND1 100-105 dumps pdf training materials and study guides free download. Update latest Cisco ICND1 100-105 dumps pdf and vce training resources from lead4pass. “Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)” is the name of Cisco https://www.leads4pass.com/100-105.html exam dumps which covers all the knowledge points of the real Cisco exam. The best Cisco ICND1 100-105 dumps exam questions and answers, pass Cisco 100-105 exam test easily at first attempt.

Latest Cisco 100-105 dumps pdf training resources free download: https://drive.google.com/open?id=0B_7qiYkH83VReEJYRlhNVjdGeVU

Latest Cisco 300-135 dumps pdf training resources free download: https://drive.google.com/open?id=0B_7qiYkH83VRS21DRS14UlZHNjg

Vendor: Cisco
Certifications: ICND1
Exam Name: Cisco Interconnecting Cisco Networking Devices Part 1 (ICND1 v3.0)
Exam Code: 100-105
Total Questions: 332 Q&As
100-150 dumps
QUESTION 1
Some routers have been configured with default routes. What are some of the advantages of using default routes? (Choose two)
A. They establish routes that will never go down.
B. They keep routing tables small.
C. They require a great deal of CPU power.
D. They allow connectivity to remote networks that are not in the routing table
E. They direct traffic from the internet into corporate networks.
Correct Answer: BD

QUESTION 2
The command ip route 192.168.100.160 255.255.255.224 192.168.10.2 was issued on a router. No routing protocols or other static routes are configured on the router. Which statement is true about this command?
A. The interface with IP address 192.168.10.2 is on this router.
B. The command sets a gateway of last resort for the router.
C. Packets that are destined for host 192.168.100.160 will be sent to 192.168.10.2.
D. The command creates a static route for all IP traffic with the source address 192.168.100.160.
Correct Answer: C

QUESTION 3
The ip helper-address command does what?
A. assigns an IP address to a host
B. resolves an IP address from a DNS server
C. relays a DHCP request across networks
D. resolves an IP address overlapping issue
Correct Answer: C

QUESTION 4
Which two of these statements are true of IPv6 address representation? 100-105 dumps (Choose two.)
A. There are four types of IPv6 addresses: unicast, multicast, anycast, and broadcast.
B. A single interface may be assigned multiple IPv6 addresses of any type.
C. Every IPv6 interface contains at least one loopback address.
D. The first 64 bits represent the dynamically created interface ID.
E. Leading zeros in an IPv6 16 bit hexadecimal field are mandatory.
Correct Answer: BC

QUESTION 5
Refer to the exhibit.
100-105 dumps
A network administrator is troubleshooting a connectivity problem on the serial interfaces. The output from the show interfaces command on both routers shows that the serial interface is up, line protocol is down.
Given the partial output for the show running-config in the exhibit, what is the most likely cause of this problem?
A. The serial cable is bad.
B. The MTU is incorrectly configured.
C. The Layer 2 framing is misconfigured.
D. The IP addresses are not in the same subnet.
Correct Answer: C

QUESTION 6
Refer to the exhibit.
100-105 dumps
Serial 0/0 does not respond to a ping request from a host on the FastEthernet 0/0 LAN.
How can this problem be corrected?
A. Enable the Serial 0/0 interface.
B. Correct the IP address for Serial 0/0.
C. Correct the IP address for FastEthernet 0/0
D. Change the encapsulation type on Serial 0/0
E. Enable autoconfiguration on the Serial 0/0 interface
Correct Answer: A

QUESTION 7
Refer to the exhibit.
100-105 dumps
A problem with network connectivity has been observed. It is suspected that the cable connected to switch port Fa0/9 on Switch1 is disconnected. 100-105 dumps What would be an effect of this cable being disconnected?
A. Host B would not be able to access the server in VLAN9 until the cable is reconnected.
B. Communication between VLAN3 and the other VLANs would be disabled.
C. The transfer of files from Host B to the server in VLAN9 would be significantly slower.
D. For less than a minute, Host B would not be able to access the server in VLAN9. Then normal network function would resume.
Correct Answer: D

QUESTION 8
Which destination IP address can a host use to send one message to multiple devices across different subnets?
A. 172.20.1.0
B. 127.0.0.1
C. 192.168.0.119
D. 239.255.0.1
Correct Answer: D

QUESTION 9
Why would a network administrator configure port security on a switch?
A. to prevent unauthorized Telnet access to a switch port
B. to prevent unauthorized hosts from accessing the LAN
C. to limit the number of Layer 2 broadcasts on a particular switch port
D. block unauthorized access to the switch management interfaces
Correct Answer: B

QUESTION 10
A receiving host has failed to receive all of the segments that it should acknowledge. What can the host do to improve the reliability of this communication session?
A. decrease the window size
B. use a different source port for the session
C. decrease the sequence number
D. obtain a new IP address from the DHCP server
E. start a new session using UDP
Correct Answer: A

QUESTION 11
Which statements are TRUE regarding Internet Protocol version 6 (IPv6) addresses? (Choose three.)
A. An IPv6 address is divided into eight 16-bit groups.
B. A double colon (::) can only be used once in a single IPv6 address.
C. IPv6 addresses are 196 bits in length.
D. Leading zeros cannot be omitted in an IPv6 address.
E. Groups with a value of 0 can be represented with a single 0 in IPv6 address.
Correct Answer: ABE

QUESTION 12
Which two statements describe the process identifier that is used in the command to configure OSPF on a router? 100-105 dumps (Choose two.)
Router(config)# router ospf 1
A. All OSPF routers in an area must have the same process ID.
B. Only one process number can be used on the same router.
C. Different process identifiers can be used to run multiple OSPF processes
D. The process number can be any number from 1 to 65,535.
E. Hello packets are sent to each neighbor to determine the processor identifier.
Correct Answer: CD

Reference: https://www.leads4pass.com/100-105.html dumps questions and answers update free try.

Watch the video to learn more: https://youtu.be/trVHfqmuVvg